Valves

The Ridart anti-syphon (pressure regulating) valves cope with higher fuel dispensing pump flow rates of up to 200 litres per minute. Fully adjustable depending on the height of the tank/head pressure of fuel, this anti-syphon (pressure regulating) valve ensures the dispensing pumps are not being overworked and prevents fuel from coming out of the pump unit air separator outlet valve. It helps to prevent fuel loss and fuel contamination. This anti-syphon (pressure regulating) valve is easy to install as it comes with 1½" female BSPT flanged inlet and outlet ports.

This Brass Check Valve is a spring loaded valve for use in pipe systems where flow is required in one direction and no return flow is allowed. These check valves can be installed in any orientation and are fitted with Female BSP threads.

The Spinsecure Tap Lock is a high security lock which fits onto the spout, for securing outdoor taps against tampering, vandalism and theft, to reduce water bills and prevent flooding. The padlock free design has no torque points for crowbar entry and when locked, spins freely and is almost impossible to remove.

This Tap Lock from Spinsecure fits most outdoor taps in gardens, holiday homes, allotments, caravan parks, golf clubs, farms and other unmanned properties and is fitted simply with no sealants, adhesives or tools required. Two magnetic keys come with the Tap Lock which are coded to match the lock and multiple taps on the same property can be keyed alike so that only one key is required for all. Version also available as a handle adaptor for regular tap use – see product images.

The Plastic Drum Tap is a larger model designed for the dispensing of larger volumes of oil from a 205litre drum. This simple and easy to install barrel tap secures onto the drum outlet when the barrel is in the horizontal position.

This Alloy Drum Tap is designed for dispensing small quantities of oil from a 205litre drum. This simple and easy to install barrel tap secures onto the drum outlet when the fuel barrel in the horizontal position. This drum tap benefits from a self-closing mechanism that prevents the accidental opening of the drum outlet that may cause a spillage.

The Piusi SEC IBC Connectors have been designed by Piusi to overcome issues associated with the traditional lever based CDS connector.

These IBC connectors work by screwing the valve open/closed without acting any angular pressure on the IBC connection point. Once connected, the SEC valve ensures that the AdBlue™ is not contaminated by the surrounding environment of the IBC tank. These come as standard with the Suzzara Blue IBC AdBlue pump kits.

The Piusi Drum Connector Filters are ideal for the quick and safe connection of a pump to a drum or tank. The integrated filter is easy to inspect and ensures that debris and large particles do not enter the pumping system and contaminate the fuel that is being dispensed.

Thanks to their flanged connection, all Piusi pumps can be easily connected without the need for sealing pastes or Teflon. These drum filters are available as three alternative options: one with filter and valve; one with just filter; and one with filter, valve and flanged outlet. The first of these models is the drum connector used on the Piusi EX50 ATEX pump kits.

This Stainless Steel Solenoid Valve is a direct acting valve, meaning that no pressure has to be applied to operate, suitable for a range of fluids including AdBlue™, fuels, oil and water. As a normally closed solenoid valve, the liquid flow is shut off until the valve is activated. When the coil integral to the valve becomes energised by an electrical current, the valve opens to enable the flow of liquid through the pipeline.

This stainless steel solenoid valve is therefore designed for situations where the fluid only needs to be released at certain intervals, for example to feed a generator with fuel from the back up storage tank. The valve could also be wired into a pump to make sure that fluid only enters the pipework from the tank when the pump is activated.

This Brass Solenoid Valve is a direct acting valve, meaning that no pressure needs to be applied to operate, for a range of fluids including fuels, oils and water. As a normally closed solenoid valve, until the valve is activated the fluid flow is shut off. When the electrical current that runs through the coil inside the valve is energised, the valve opens and allows the flow of liquid through the pipework.

This brass solenoid valve is therefore designed for applications where fluid only needs to be released on occasions, such as to feed a generator with diesel from the back up storage tank. It could also be wired into a pump ensuring that fuel only enters the pipework from the tank when the pump is turned on.

The Locking Angle Brass Gate Valve is used primarily on the bottom outlet of a gravity fed diesel storage tank. These gate valves are designed to come out at 90º to take away the pressure on the hose, and to maximize the flow rate through the delivery hose without restriction.

The locking lever on these gate valves allows it to be padlocked when not in use. This angle gate valve is supplied as standard on some of our Gravity Hose Kits.

The Brass Gate Valve is a standard gate valve which can be used for a variety of applications, including on some of our Gravity Hose Kits. These gate valves are designed for starting/shutting off flow. The gate valves are used within fuel and water installations, and are suitable for use with diesel, oil and water.

Brass Body & Bonnet, Cast Handwheel, Screwed BSPT. PN20 rating, Temperature -20°C to 120°C.

The Stainless Steel Lockable Lever Ball Valve is designed for applications where brass is not suitable. This version of ball valve is therefore used for installations with more aggressive fluids such as AdBlue™ and chemical fluid pipelines. The lockable lever ball valves can be locked using a padlock in either the open or closed position, and the locking device covers the stem nut, which means that if the padlock is on, the lever is impossible to remove.

This valve us fatted with an Anti-blowout stem and PTFE seals. PN63 Rating, Temperature -10°C to 180°C.