220 Litre Harlequin Portable Diesel Dispensing Tank

This 2500-litre Slimline Fuel Station, one of the two narrowest diesel dispensing tanks within the Harlequin range, is an ideal choice for any on-site refuelling requirement especially where space is limited. It’s environment-friendly bunded design allows it to safely store and dispense fuel in any small commercial, industrial or agricultural environment. This simple and easy to use diesel storage and dispensing solution is manufactured from high-quality mouldings and materials. It can be customised further by adding fuel dispensing accessories such as a high-speed fuel pump and a fuel management system.

Features:

Fully Bunded

56L/min 240Volt fuel pump

Mechanical flow meter

10Micron particulate & water filter

6m length; 1” delivery hose

Auto shut-off nozzle

Bulkhead light

2” BSP fill point

4” lockable inspection port

LRC overfill prevention probe

Electronic Level Gauge

Optional Extras (Additional Cost):

72L/min fuel pump

Fuel Management System

Installation:

Base Length: 2,550mm

Base Width: 1,385mm

This 350-litre capacity vertical environment-friendly bunded oil tank is suitable for the storage of heating oil in a domestic or commercial set up. It's ideal for use when additional tank technology is not a requirement. Made from Medium Density Polyethylene (MDPE), this tank is lightweight, durable, non-corrosive, simple to install and aesthetically pleasing.

The Harlequin 350HQI Comes complete with -

Integrally bunded

Bottom outlet with 1" BSP(F) thread

4" lockable inspection/fill cap

32mm hole with cover for electronic gauge

Inner tank vent

10 Year guarantee

This Horizontal, cylindrical bulk diesel tank with a double skin design is constructed from mild steel plate to BS EN 10025.

The inner tank provides the required storage area, whilst the outer tank forms the required bund with capacity of 110% of the total liquid being stored. The tank vent is piped into the bund and then to the atmosphere further reducing the risk of spills in the event of overfilling the tank.

These tanks are fitted with steel base supports to eliminate ground contact with the tank base.

This Cylindrical fuel tank can be supplied with either a lockable fill point cabinet or full size inset cabinet to house any ancillary equipment fitted with lockable steel or roller shutter door.

Specification:

1 x 2” tank to bund vent.   1 x 2” atmospheric vent with cap.   1 x Bund contents test and drain point with dial gauge. 1 x 2” Base feed with isolation valve.   1 x 2” Top feed with foot valve and strainer.   1 x 2” socket for tank contents. 1 x 2” Socket fill point.   4 x lift points (lift empty only).   1 x 1” socket in bund for optional bund alarm probe.

1 x 2” socket in top of tank for optional high / low alarm probes.     1 x 600mm Service hatch.     Base support: Tank support cradles with ground anchor points.

Paint finish: ISO 12944 C3 Compliant coating. Application design life: 7 years. Typical environments include: Urban and industrial atmospheres, Moderate sulphur dioxide levels, production areas with humidity.

Compliancy:

BS799 Part 5. PPG2, DSEAR 2002

Control of Pollution (Oil Storage) (England) Regulations,

Environment (Oil Storage) (Scotland) Regulations,

Control of Pollution (Oil Storage) Regulations (Northern Ireland),

Control of Pollution (Oil Storage) (Wales) Regulations.

This 1350 Litre Rototek 3C Centurion Bunded Oil Tank is ideal for the safe, secure and environmentally responsible storage of heating oil. Rotationally moulded in the United Kingdom from a high grade Medium Density Polyethylene which is tough, durable and UV Stabilised to prevent colour fade.

The tanks come fully assembled and with an optional installation kit, making the tank simple and ready to install by an approved engineer.*

*Please note that all oil tanks should be installed by a suitably competent person in accordance with statutory requirements.

These bunded oil tanks come with a 10 year warranty if installed by an Oftec Approved Engineer and subsequently inspected annually by an Oftec Approved Engineer.

Standard fittings and parts supplied with the tank:

1” BSP Bottom Outlet

2 x 2 Inch Vents

Lockable Manhole Lid

4” Inspection aperture with lockable screw cap

Optional Fittings:

Apollo Bund alarm with plug in receiver

Float Level Gauge

Atkinson Installation Kit Comprising of:

1-0.5 inch reducer

Fuel Filter with lever type isolation valve

PTFE and Heldite thread sealant